Fermentation started, then stopped the next day. Is my yeast dead?

Question

Fermentation started, then stopped the next day. Is my yeast dead?

jeremytrimble

2017年10月3日 15:39

This is my first shot at homebrewing, using Northern Brewer's American Wheat Beer kit which is based on liquid malt extract, Willamette and Cascade hops, and a packet of dry yeast. I brewed and put the hopped wort into fermentation on Friday. By Sunday morning (~40 hours later), fermentation seemed to be moving along at a good clip -- I could see bubbles traveling through the airlock about once every 2 seconds.

However, by Monday morning, bubbling had completely stopped. The weather (and my house) had gotten considerably cooler overnight, so thinking the cold was to blame, I moved the fermenter into the warmest room in the house (which still probably never goes over 70 Fahrenheit). Still, no bubbling as of Tuesday evening.

I was under the impression that fermentation should be vigorous for at least a few days.

I've been doing some research and realize now that when I was brewing I didn't really understand the importance of aerating the wort. I shook it around for a minute or so in the fermenter on brewing day, but maybe that wasn't enough? Also, I didn't realize until brewing day that I should have been keeping the dry yeast packet in the fridge/freezer -- it had been sitting out in my basement (60-75 Fahrenheit) for at least a month. Oops.

Any thoughts on if I screwed something up or if there's a way to fix it (if it really needs fixed)?

I'd appreciate any help. Thanks!

Update: At the suggestion of Denny (and some other homebrewers I talked to in person), I decided to just let the fermentation run its course and I'm happy to report that fermentation seems to have worked -- my original gravity was 1.041 (possibly slightly higher as the reading was taken warm) and after two weeks on bottling day I was at 1.016 = 60% attenuation (right?). Although the Safale US-05 Ale Yeast I used doesn't give attenuation specs, some folks on a forum said they usually get at least 70% from that strain, so it's possible that fermentation might have been a little stunted from the yeast not being refrigerated.

The beer is conditioning in the bottles now, so hopefully it will taste good when I crack one open in a couple weeks. Thanks everyone for all the input -- if nothing else I've learned the importance of taking good care of the yeast.

Topic aeration yeast fermentation homebrew

Category Mac

Denny Conn · Accepted Answer · 2017年10月3日 15:39

Bubbling really tells you nothing other than CO2 is being released. It's not a reliable indicator of fermentation.

In addition, if you ferment in a bucket and have a loose seal you won't see bubbles. Aeration is needed so that the yeast can use the O2 to synthesize sterols to build new cells. Because the cell count in dry yeast is so much higher than liquid yeast, aeration is much less important. Your yeast should have been kept refrigerated, though, so the cell count may be down a bit. It probably wasn't a fatal mistake.

In short, I wouldn't worry. Give it a week or so, then take a gravity reading to see where you're at.

Dancan123 · Accepted Answer · 2017年6月13日 12:58

If you used a plastic bucket and lid for primary fermentation, there are basically two types of buckets and lids. The cheaper ones are designed without a rubber gasket or o-ring in the lid. I used these for a while and experienced what you did every time. As pressure builds in the bucket, CO2 escapes through the seal between the lid & the bucket. Thus reducing the visual effect through your airlock. When I purchased the set up with an o-ring in the lid, fermentation was visible through the air lock for 5-7 days although the visual effect slowed down considerably. I have since replaced all my buckets with lid types as the visual effect lets me know when fermentation is really winding down.

Chris Plaisier · Accepted Answer · 2012年1月18日 20:18

Previously I was mistaken. Yeast do not abide by the same rules as mammalian cells which I am familiar, who prefer aerobic respiration when there is oxygen. Instead when yeast are introduced into the wort (which is over 1% by weight sugar), regardless of the presence of oxygen, they immediately enter fermentation and begin producing ethanol. This is called the Crabtree effect and is probably induced because they yeast want to use the O₂ create sterols that are required to make more yeast. Apparently the yeast trade off a more efficient respiratory process for growth.

The sugar from the wort is thus fermented and during this process CO₂ is released in the final step where lactic acid is converted into ethanol and CO₂. For each of the glucose molecules produces 2 molecules of ethanol and CO₂. Thus the bubbling observed in beer fermentation comes from fermentation which is initiated at pitching of the yeast. The yeast are using primarily anaerobic respiration and also dividing simultaneously.

In answer to your question your beer is likely going to be fine. I typically wait till the yeast has dropped out of suspension (flocculated) to make a layer on the bottom of the fermenter. That usually means the yeast are done and it is time to bottle. Just make sure to take hydrometer readings after a week or so and bottle or keg when it reaches the final gravity you want.

Fermentation started, then stopped the next day. Is my yeast dead?

About